Skip to content
  1. Home
  2. Stress relief annealing

Core service

Stress relief annealing

Annealing to reduce residual stresses in large weldments, with a controlled cycle and an annealing chart.

What is stress relief annealing

Lower residual stress, more predictable machining

Stress relief annealing is a heat treatment that reduces residual stresses in a metal part without significantly changing its basic microstructure.

For steel weldments we carry it out after welding (post-weld heat treatment, PWHT), when the effect of stresses caused by uneven heating and shrinkage of the welds needs to be reduced. It is also used for parts after machining and other processes that introduce internal stresses.

  • Weldments up to 12.8 m long and 100 t
  • Heat treatment cycle to your specification
  • An annealing chart for every cycle
Weldment on a furnace car entering the annealing furnace

Where stresses come from

Why residual stresses remain in metal

Residual stresses remain in the material even when no external force acts on the part. They are caused by welding, rolling, bending, forging, casting and machining.

EXAMPLE 1

Welding

The weld zone heats up strongly and expands, but the cooler surrounding material restrains it. After welding, the weld cools and shrinks, though not at the same rate as the rest of the structure. Part of the stress stays in the part even after it has cooled down.

EXAMPLE 2

Machining

A large welded structure is milled after welding. Removing material changes the balance of stresses, parts of the structure may move and the part ends up out of tolerance. Annealing before the critical machining stage reduces this risk.

Objectives

What stress relief annealing achieves

01

Lower residual stress

A controlled cycle reduces part of the stresses introduced during manufacturing.

02

Dimensional stability

Lower risk of movement and distortion during further processing.

03

Ready for precision machining

With tight tolerances, annealing is often an essential step in the production sequence.

04

Controlled process

Correctly chosen heating, soaking and cooling limit new thermal stresses.

05

Material properties retained

The aim is to reduce stresses without major unwanted changes to the microstructure or mechanical properties.

06

Proof of treatment

The annealing chart shows the course of the cycle and can accompany the part documentation.

Process

Stress relief annealing in six steps

Annealing is not just heating a part to a given temperature. Every phase of the cycle matters.

  1. 1

    Preparation and procedure

    We check the material, dimensions, weight, geometry and the required cycle, plus any requirements for thermocouples and documentation.

  2. 2

    Loading into the furnace

    We crane the weldment in and support it according to its weight, shape and thermal expansion. Hollow sections are vented for pressure equalisation.

  3. 3

    Controlled heating

    The heating rate is matched to the material and size, as the surface and core of a heavy part heat up at different rates.

  4. 4

    Soaking at temperature

    The part is held at the required temperature for as long as the procedure specifies. This is where much of the stress is relieved.

  5. 5

    Controlled cooling

    We cool to the specified regime, often together with the furnace, so that no new temperature differences arise.

  6. 6

    Completion and records

    We review the temperature record. You receive the annealing chart with the part, plus a report when thermocouples are used.

Heat treatment cycle

Heating, soaking, cooling

For structural steels, technical literature often cites a range of approximately 450–650 °C, but this is not a general rule. The actual temperature depends on the chemical composition, condition of the material, part dimensions and the specified procedure.

With a heavy part it is not enough for the furnace sensor to reach the set temperature. What matters is when the material reaches it. That is why in furnaces 3 and 4 we can measure the temperature directly on the weldment.

Measurement and documentation
Heating Soaking Furnace cooling In air soak temperature °C time furnace temperature part temperature (thermocouple)
Schematic stress relief annealing cycle. Actual temperatures and times are defined for each part.

Suitable parts

What we anneal most often

We check suitability for each part individually, as different steels behave differently when heated.

  • large welded structures and heavy weldments
  • welded machine components
  • structures before precision machining
  • parts with complex geometry and tight tolerances
  • parts where annealing is specified in the technical documentation
Heavy weldment in an open furnace

Comparison

Stress relief annealing and other annealing processes

The processes differ in purpose, temperature, soaking time and cooling rate, so they cannot be used interchangeably.

Annealing processMain purpose
Stress relief annealingReducing residual stresses with minimal change to the basic microstructure.
Soft annealingReducing hardness and improving the machinability of certain steels.
Recrystallisation annealingRemoving the effects of strain hardening after cold forming.
NormalisingRefining the steel microstructure for a more suitable structure and properties.
Diffusion annealingReducing chemical inhomogeneity by diffusion at high temperatures.
Stress relief annealing is not hardening. In hardening, steel is cooled rapidly to change its microstructure and mechanical properties. In stress relief annealing the aim is to reduce stresses while preserving the material properties as far as possible.

Heat treatment regime

What the right cycle depends on

There is no single programme that suits every weldment. Before we start, we take all of the factors below into account.

01

Material grade

Different steels have different compositions and heat treatment limits.

02

Wall thickness

Heavy sections heat up and cool down differently from thin-walled ones.

03

Geometry

Hollow sections and uneven thicknesses affect heat transfer.

04

Size and weight

A larger thermal mass means a different cycle design.

05

Customer requirements

Specifications may set temperature, time, rates and measurements.

06

Further processing

It matters whether the part will be milled, drilled or welded after annealing.

Sequence

Annealing before machining

If annealing is specified or technically advisable, we carry it out before the critical machining stage. A typical sequence is:

  1. manufacturing the individual parts,
  2. assembling and welding the structure,
  3. inspection and preparation of the weldment,
  4. stress relief annealing,
  5. further machining,
  6. final dimensional inspection.

The final sequence is set by the responsible engineer based on the design and requirements of the part.

Weldment on the annealing furnace car
Important limitation: stress relief annealing alone does not guarantee that a part will be free of distortion, cracks or other defects. The result depends on the correct choice of procedure, material, design and other production conditions.

FAQ

Questions about stress relief annealing

Crane lifting a weldment in the Termis yard
Does stress relief annealing remove all residual stresses?
Not necessarily. The aim is to reduce residual stresses. The degree of reduction depends on the material and the selected procedure.
Does stress relief annealing change the strength of steel?
A correctly chosen procedure reduces internal stresses without significant unwanted change to the basic microstructure. The actual effect depends on the steel grade, its initial condition and the heat treatment cycle.
How long does annealing take?
It depends on the heating rate, part size, soaking time and cooling rate. For large structures the whole cycle takes considerably longer than the soak alone. You get the exact date with your quotation.
Can annealing prevent distortion during milling?
It can reduce the risk of distortion caused by residual stresses. It cannot guarantee there will be none, as distortion also depends on the part design, clamping and machining method.
Can you anneal very large structures?
We have four furnaces: the longest takes parts up to 12.8 m, another up to 100 t. We check suitability for each weldment based on its dimensions, weight and required cycle.
Do I receive a temperature chart?
Yes. An annealing chart is generated automatically at the end of every cycle. With thermocouples on the part we also issue a report.
What information should I send with my enquiry?
Material, dimensions, weight, quantity, the required heat treatment cycle, any requirements for thermocouples and documentation, and your preferred date. If possible, attach a technical drawing.

Enquiry

You send the drawing. We choose the right furnace.

Dimensions, weight and material are enough for us to check which furnace fits and confirm a date.

Send an enquiry
Phone+386 40 529 312
Emailinfo@termis.si
Address
Zagrebška cesta 20
2000 Maribor, Slovenia